Zones stuck on, zones that won't come on, weeping heads and valves nobody can find. We diagnose the valve, solenoid or wiring and fix it properly the first time.
Every zone in your system is opened and closed by one valve. When a valve fails, you get a flooded zone, a dry zone, or a water bill that makes no sense. These are the valve problems we're called out for most often across Tampa Bay.
A zone that keeps running after the controller turns it off is usually a valve problem. Most often, sand, a pebble or reclaimed-water grit is caught under the diaphragm. Other causes are a torn diaphragm, a clogged bleed port, or a solenoid that's stuck open or was left loosened after someone ran the zone by hand.
What to do right now: shut off the irrigation supply at the backflow or the shut-off valve. Then call us. A zone that runs all day wastes thousands of gallons and can get you a county watering-day violation. See our Tampa Bay watering restriction guide.
Water bubbling out of the lowest head in a zone hours after watering is the classic sign of a valve that isn't sealing completely. We tell this apart from normal low-head drainage. Then we clean or replace the diaphragm, or replace the valve if the body or seat is cracked. Where the yard slopes, we add check valves so the pipe doesn't drain out through the low heads.
When one zone is dead and the rest run fine, the cause is usually the solenoid, a corroded wire splice in the valve box, or a cut zone wire. Wires often get cut by fence posts, landscapers or new sod. We test each zone's wiring from the controller with a multimeter, check the solenoid's resistance, and fix it. That might mean replacing the solenoid, making waterproof splices, or running a new wire. We don't just keep swapping parts.
If several zones fail at once, the problem may be the controller instead. See our controller repair & smart controller upgrades.
On older Tampa properties, valves are often buried under sod, mulch or pavers with no box at all. Our wire and valve locator traces each zone wire to its solenoid, so we dig one small hole instead of trenching across your lawn.
When a valve manifold (several valves grouped in one box) is cracked, root-bound or full of mismatched old valves, we rebuild it. That means new valves, clean glued joints, unions so future service is easy, and a properly sized valve box set at grade.
Real photos from our own job sites, not stock images: buried valves, valve replacements, manifold rebuilds and reclaimed water valve boxes around Tampa Bay.
We carry common diaphragms, solenoids and replacement valves on the truck, so most repairs are finished on the first visit, whoever installed your system.
DV, JTV and ASVF anti-siphon valves, plus the PGA and PEB valves found on larger lots. We do diaphragm kits, solenoid swaps and full replacements.
PGV inline and anti-siphon valves, the workhorse of most Tampa Bay homes. We repair and replace PGV and ICV valves, including flow-control adjustment.
Toro EZ-Flo and 250-series valves and Irritrol 700/2400-series valves, common in 1990s–2000s builder installs around Carrollwood and Brandon.
Orbit anti-siphon and inline valves from DIY installs. These often crack in the Florida sun, so we usually upgrade them to a commercial-grade valve.
As a K-Rain Premier partner, we service K-Rain inline valves and indexing valves with factory parts.
Older Tampa, Carrollwood and Seffner systems on wells often use one water-driven indexing valve instead of electric zone valves. When zones skip or water runs out of order, we rebuild or replace the indexing valve and its cam so it matches your zone count.
Valves fail differently depending on where your water comes from, so here's what we see most in each area.
Across Tampa, we see everything from 40-year-old brass valves in South Tampa to plastic manifolds buried under St. Augustine sod in North Tampa. On city potable and reclaimed water, the most common call is a zone that won't shut off because grit is caught under the diaphragm. Citywide repair details are on our Tampa irrigation page.
Many Wesley Chapel and New Tampa neighborhoods run on reclaimed water. You'll see purple pipe and purple valve-box lids. Reclaimed water carries more sediment and organic matter than drinking water, and it clogs diaphragm bleed ports and solenoid screens. That's why zones stick on or weep here more than anywhere else. See our Wesley Chapel sprinkler repair page for more.
In Original Carrollwood, mature live oaks and laurel oaks are beautiful, but their roots crush valve boxes and crack manifolds. Many older systems there also run on indexing valves or valves buried with no box. Locating, rebuilding the manifold and resetting a proper valve box is a common job for us in Carrollwood.
Most homes in Seffner and Thonotosassa irrigate from shallow private wells. Iron and fine sand from the well wear out diaphragms quickly, and well pump pressure that's too high or that cycles on and off strains valves. We often pair valve repair with a pressure and well pump check so the new valve lasts.
Brandon has many 1990s and early-2000s builder systems with original Toro and Irritrol valves that are now past their service life. Their solenoids and diaphragms fail one after another. When three or four valves on one manifold are failing, replacing the whole manifold usually costs less than repairing valves one at a time.
Temple Terrace yards near the Hillsborough River have sandy soil and big tree canopies. Valve boxes settle, fill with sand and get buried under leaf litter until no one remembers where they are. We locate those valves, clear and raise the boxes, and replace corroded wire splices that cause zones to cut in and out.
We also handle valve repair in Lutz, Odessa, Westchase, Lake Magdalene, Tampa Palms and the rest of Hillsborough and southern Pasco County. If a zone is stuck on, please shut off the water. Florida watering restrictions apply whether the extra watering is on purpose or not. Learn more about our full sprinkler repair service or maintenance plans that catch failing valves early.
We run every zone from the controller and note which ones stick, weep, or don't respond.
We trace wires to buried valves, test solenoid resistance, and open the valve to inspect the diaphragm and seat.
We give you a firm price first, then rebuild, replace or re-manifold using quality parts and waterproof wire connectors.
We confirm each zone opens and closes fully and the low heads stop weeping, and we leave the valve box accessible.
"They came out at 7pm for an emergency repair to my irrigation system. They were very professional and their customer service rocks. Dan was responsive and the price was good."
"Excellent experience with Water Oak and Dan! Even in the pouring rain, Dan got the job done on our sprinkler system. Would definitely recommend and will use again."
"Dan is a friendly, knowledgeable guy. He gave a clear explanation of what we needed and took care of it efficiently. He didn't try to talk us into unnecessary extras. Would highly recommend."
Valve repair costs depend on what failed, how many valves are involved, and whether the valve has to be found first. Here's how the common jobs compare.
| Repair | When it's needed | Typical cost |
|---|---|---|
| Valve cleaning or flush | Grit or reclaimed-water sediment is holding a zone open | Lowest cost |
| Solenoid replacement | One zone won't turn on and the wiring tests good | Less than a full valve |
| Diaphragm rebuild | Low heads weep after the zone shuts off, but the valve body is sound | Less than a full valve |
| Full zone valve replacement | Cracked body, worn seat or an obsolete valve | $150–$350, including solenoid and valve body |
| Buried valve locating or wire repair | No valve box, or a zone wire cut by digging or fence posts | Adds labor time |
| Manifold rebuild | Several old or failing valves in one box | Highest; every valve is replaced and pressure-tested |
We diagnose the problem and give you a firm price before any work begins. When three or more valves on one manifold are failing, replacing the whole manifold usually costs less than repairing them one at a time.
A full zone valve replacement in Tampa typically runs $150 to $350, including the solenoid and valve body. Cleaning a valve or replacing just the solenoid or diaphragm usually costs less. Rebuilding a manifold, where several valves sit together in one box, costs the most because every valve in that box is replaced and pressure-tested. Locating a buried valve or tracing a broken wire adds labor time. We diagnose the problem and give you a firm price before any work begins.
If water keeps seeping out of the lowest heads in a zone after it shuts off, the valve is not sealing completely. The usual causes are debris or reclaimed-water sediment caught under the diaphragm, a torn or stiff diaphragm, a clogged bleed port, or a cracked valve body. Low-head drainage, where the pipe simply empties out of the lowest head, looks similar but stops after a few minutes. A leaking valve keeps weeping. We test the zone to tell the two apart, then clean, rebuild or replace the valve.
Yes. We use a valve and wire locator that sends a signal down the zone wire from the controller and tracks it to the solenoid underground, so we dig one small, targeted hole instead of trenching across your lawn. Once we find the valve, we can install a proper valve box so it is easy to reach the next time.
Most residential irrigation valves last about 10 to 15 years in Tampa Bay. Reclaimed water, well water with iron or sand, and high water pressure wear out diaphragms and solenoids faster. Valves in boxes that flood or fill with sand also fail sooner. If your system still has its original builder valves from the 1990s or early 2000s, expect them to start failing one after another.
If the valve body is sound, cleaning it or replacing the solenoid or diaphragm is usually the cheaper fix. Replace the valve if the body or seat is cracked, if parts for it are no longer made, or if it keeps failing after repairs. When several valves on one manifold are failing, rebuilding the whole manifold usually costs less than repairing each valve separately.
Usually, yes. Same-day valve repair is available for most of Tampa Bay. We carry common Rain Bird, Hunter, Toro, Irritrol, Orbit and K-Rain valves, solenoids and diaphragms on the truck, so most repairs are finished on the first visit.
A zone that runs when the controller isn't calling for it usually has a valve that isn't closing fully. Debris under the diaphragm or a clogged bleed port lets water slowly push the valve open. Less often, the cause is a solenoid left loose after someone ran the zone by hand, a stray voltage problem in the wiring, or a controller with a stuck relay. We test the valve and the controller to find which one it is.
Shut off the irrigation supply, then call us. Same-day valve repair is available for most of Tampa Bay.